{"product_id":"tsmb-anlegesensor-gefedert-io-link-mkts-spio","title":"TSMB Contact Sensor Spring-Loaded IO-Link (MKTS-SPIO)","description":"\u003cp\u003eThe \u003cstrong\u003eTSMB\u003c\/strong\u003e is a contact sensor with a spring-loaded measuring tip and an IO-Link interface, manufacturer type Müller \u003cstrong\u003eMKTS-SPIO\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003eIt measures on the surface and in bearings: The compression spring holds the measuring tip with a \u003cstrong\u003e14 mm travel (±1 mm)\u003c\/strong\u003e at the measuring point, even if the component moves or expands due to heat – a rigidly screwed-in sensor would lose contact in such a situation. The sensor tube measures \u003cstrong\u003eØ 6 mm\u003c\/strong\u003e made of stainless steel \u003cstrong\u003e1.4571\u003c\/strong\u003e, the compression spring is made of spring steel \u003cstrong\u003e1.4310\u003c\/strong\u003e, the protection class is \u003cstrong\u003eIP 65 \/ IP 68\u003c\/strong\u003e, the installation length is \u003cstrong\u003e45 or 65 mm\u003c\/strong\u003e, the weight is approximately \u003cstrong\u003e200 g\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003eThe mechanics are the same as with the \u003cstrong\u003eTSMA\u003c\/strong\u003e (MKTS-SP); instead of a HART transmitter, an IO-Link transmitter is installed here. The measured value is sent digitally to the \u003cstrong\u003eIO-Link\u003c\/strong\u003e master, and the sensor is also parameterized there – a configuration device is not necessary, the description of the values is in the device file \u003cstrong\u003eIODD MKTS-SPIO\u003c\/strong\u003e. The electrical connection is \u003cstrong\u003eM12x1 four-pin\u003c\/strong\u003e as the only option; the sensor does not have a display or limit contacts.\u003c\/p\u003e\u003cp\u003eThe input has \u003cstrong\u003ea Pt100\u003c\/strong\u003e in a \u003cstrong\u003e3-wire circuit\u003c\/strong\u003e or a thermocouple \u003cstrong\u003eType J, K or N\u003c\/strong\u003e. The nominal range extends from \u003cstrong\u003e-50 … +150 °C\u003c\/strong\u003e in all versions; a measuring range of \u003cstrong\u003e0 … 100 °C\u003c\/strong\u003e is set ex works, customizable. The source states the accuracy as \u003cstrong\u003emax. 0.02 % of the range\u003c\/strong\u003e plus sensor error at \u003cstrong\u003e16 Bit\u003c\/strong\u003e and \u003cstrong\u003e20 ms\u003c\/strong\u003e response time, powered by \u003cstrong\u003e24 VDC\u003c\/strong\u003e with reverse polarity protection.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNote before ordering:\u003c\/strong\u003e This sensor does not withstand process pressure. The source explicitly states: System pressure not possible, the process connection has no sealing effect; the Pressure Equipment Directive is therefore not applicable. The ambient temperature is not the medium temperature: The electronics in the head tolerate \u003cstrong\u003e-20 … +80 °C\u003c\/strong\u003e, the medium up to +150 °C; the source does not state what neck length or insulation is required for this. The accuracy specification is remarkably favorable: 0.02 % of the range at 16 Bit, while the sister sheets with 24 Bit only guarantee 0.1 % and the MKTS-SP with the same design states 0.3 % – before designing, the value must be confirmed with the manufacturer, the sensor error is always added. The relationship between filter and response time is also striking: 25 s filter at 20 ms response time. The datasheet does not specify a minimum span. A CE mark is not documented, a declaration of conformity is not available; explosion protection is also not documented.\u003c\/p\u003e\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\u003cul\u003e\n\n\u003cli\u003eSpring-loaded measuring tip, travel 14 mm ±1 mm\u003c\/li\u003e\n\n\u003cli\u003eIO-Link with signal level 0\/24 V, parameterization via the master\u003c\/li\u003e\n\n\u003cli\u003eRange -50 to +150 °C, factory setting 0 … 100 °C\u003c\/li\u003e\n\n\u003cli\u003eInstallation length 45 or 65 mm, sensor tube Ø 6 mm made of 1.4571\u003c\/li\u003e\n\n\u003cli\u003eVersion with HART available as TSMA\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"octogon GmbH","offers":[{"title":"Default Title","offer_id":57356932645190,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TSMB_produkt_1b00777b-4c87-4666-b6a6-cf34fa5127d4.webp?v=1789243718","url":"https:\/\/octogon-sensors.com\/en\/products\/tsmb-anlegesensor-gefedert-io-link-mkts-spio","provider":"octogon GmbH","version":"1.0","type":"link"}