{"title":"Temperatur - Anlegen \u0026 berührungslos","description":"\u003ch2\u003eAnlege- und berührungslose Temperaturfühler\u003c\/h2\u003e \u003cp\u003eWenn die Leitung nicht geöffnet werden darf oder kein Prozessanschluss vorhanden ist, wird von außen gemessen. Der Fühler wird an das Rohr oder das Bauteil angelegt – magnetisch oder gefedert – oder er misst ganz ohne Kontakt über die Wärmestrahlung.\u003c\/p\u003e \u003cp\u003eDer Einbau geht ohne Stillstand und ohne Eingriff in den Prozess. Dafür misst man die Oberflächentemperatur und nicht die des Mediums: je nach Isolierung und Strömung liegt sie darunter. Zur Auswahl stehen \u003ca href=\"\/en\/collections\/temperatur-magnetisch-tm\"\u003emagnetische Oberflächenfühler\u003c\/a\u003e, \u003ca href=\"\/en\/collections\/temperatur-feder-kontakt-ts\"\u003egefederte Anlegefühler\u003c\/a\u003e und \u003ca href=\"\/en\/collections\/temperatur-infrarot-ti\"\u003eInfrarotsensoren\u003c\/a\u003e. Wo der Prozess geöffnet werden kann, ist ein \u003ca href=\"\/en\/collections\/temperatur-einbau-im-prozess\"\u003eFühler im Prozess\u003c\/a\u003e genauer.\u003c\/p\u003e","products":[{"product_id":"tdma-infrarot-temperatursensor-mets-ir","title":"TIMA Infrared Temperature Sensor (METS-IR)","description":"\u003cp\u003eThe \u003cstrong\u003eTIMA\u003c\/strong\u003e is an infrared temperature sensor for non-contact measurement, manufacturer type Müller \u003cstrong\u003eMETS-IR\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIt measures on moving, hot or delicate surfaces without touching the medium – where a protective tube would be in the way or cannot be installed at all. Housing, display and the two limit contacts are the same as on the screw-in sensors of the series.\u003c\/p\u003e\n\u003cp\u003eThe sensor evaluates infrared radiation in the spectral range \u003cstrong\u003e8 … 14 µm\u003c\/strong\u003e and covers \u003cstrong\u003e-40 … +1000 °C\u003c\/strong\u003e, with a minimum span of 100 °C. The optical resolution is \u003cstrong\u003e15:1\u003c\/strong\u003e. Accuracy is \u003cstrong\u003e±1.5 °C or ±1.5 %\u003c\/strong\u003e – whichever is greater applies – repeatability ±0.75 °C or ±0.75 %, resolution 0.1 K. Emissivity and transmissivity are adjustable from 0.100 to 1.100 in software. The response time is \u003cstrong\u003e30 ms\u003c\/strong\u003e (t90) at 10 measurements per second.\u003c\/p\u003e\n\u003cp\u003eThe output is \u003cstrong\u003e4 … 20 mA with HART\u003c\/strong\u003e in 3-wire technology, current range 3.8 … 20.5 mA, with a fault signal at 3.6 mA (short circuit) and 21 mA (break). Added to that: a 4-digit 7-segment display in the head, which rotates through \u003cstrong\u003e330°\u003c\/strong\u003e, and \u003cstrong\u003etwo limit contacts\u003c\/strong\u003e, PNP or NPN, 30 VDC \/ 200 mA. Supply is \u003cstrong\u003e24 VDC ±10 %\u003c\/strong\u003e through an eight-pin M12×1 connector – the only connection on this product.\u003c\/p\u003e\n\u003cp\u003eMechanically: process connection from 1\/4\" to 1\" as well as 1\/4NPT to 1\/2NPT, protective tube in 1.4571, Ø 6 × 0.5 mm, 100 mm neck tube optional, PBT GF30 housing, stainless steel measuring head, weight approx. 240 g, protection at least \u003cstrong\u003eIP 65\u003c\/strong\u003e with encapsulated boards. Vibration to IEC 68-2-6, shock to IEC 68-2-27.\u003c\/p\u003e\n\u003cp\u003eThree things belong in the planning. \u003cstrong\u003eThe measuring spot grows with distance\u003c\/strong\u003e – 6.5 mm at the front edge, 16.6 mm at 200 mm, 76.5 mm at one metre; the target must be at least as large as the spot. \u003cstrong\u003eThe ambient temperature is not the medium temperature\u003c\/strong\u003e – the electronics in the head tolerate -20 … +80 °C, the measuring head -20 … +120 °C. And this product measures against the \u003cstrong\u003eopen atmosphere\u003c\/strong\u003e, system pressure 0 bar; it does not belong in a pressurised space, whereas the other sensors of the series withstand PN 25. After 10 minutes of warm-up the reading is dependable.\u003c\/p\u003e\n\u003cp\u003eProgramming requires the \u003cstrong\u003eDEV-KMA\u003c\/strong\u003e configurator with the TrComm software. No CE marking is documented in the manufacturer's data sheet, no declaration of conformity is available, and one must be requested before placing the product on the market in the EU. No explosion protection is documented.\u003c\/p\u003e\n\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eNon-contact measurement from -40 to +1000 °C\u003c\/li\u003e\n\u003cli\u003eOptical resolution 15:1, spectral range 8 … 14 µm\u003c\/li\u003e\n\u003cli\u003eAccuracy ±1.5 °C or ±1.5 %, resolution 0.1 K\u003c\/li\u003e\n\u003cli\u003eResponse time 30 ms, 10 measurements per second\u003c\/li\u003e\n\u003cli\u003e4 … 20 mA with HART, 3-wire\u003c\/li\u003e\n\u003cli\u003eDisplay in a head that rotates through 330°\u003c\/li\u003e\n\u003cli\u003eTwo limit contacts, PNP or NPN\u003c\/li\u003e\n\u003cli\u003eEmissivity adjustable in software\u003c\/li\u003e\n\u003cli\u003eProtection at least IP 65\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"octogon Shop","offers":[{"title":"Default Title","offer_id":57245618635078,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TIMA_METS-IR_titelbild_c209e1a8-b964-4983-b7ef-4486cbc6379a.webp?v=1788951931"},{"product_id":"temperatursensor-magnetisch-mets-wtm","title":"TMMB Magnetic Surface Temperature Sensor (METS-WTM)","description":"\u003cp\u003eThe \u003cstrong\u003eTMMB\u003c\/strong\u003e is a surface temperature sensor on a holding magnet, manufacturer type Müller \u003cstrong\u003eMETS-WTM\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIt is placed on a pipe or a vessel and holds itself – no drilling, no process connection, no intervention in the medium. The spring-loaded measuring face presses against the surface, the magnet pulls with \u003cstrong\u003e66 N\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis device has no display and no keys\u003c\/strong\u003e – it is set exclusively over HART. Otherwise it is identical to the \u003cstrong\u003eTMMA\u003c\/strong\u003e (METS-WSM), which carries the display. Anyone who wants to read the value on site orders the TMMA.\u003c\/p\u003e\n\u003cp\u003eThe input is a \u003cstrong\u003ePt100 in 4-wire connection\u003c\/strong\u003e in classes A, B and AA (B 1\/3 DIN), with a range of \u003cstrong\u003e-50 … +200 °C\u003c\/strong\u003e at a smallest span of 50 K; up to -50 … +250 °C on request. The output is \u003cstrong\u003e4 … 20 mA with HART\u003c\/strong\u003e in the 2-wire loop, current range 3.8 … 20.5 mA, with 3.6 mA on short circuit and 21 mA on break. Accuracy is \u003cstrong\u003e0.3 % of the range\u003c\/strong\u003e at \u003cstrong\u003e16 bit\u003c\/strong\u003e, the response time 20 ms, the measuring rate 10 measurements per second, the filter 0 … 99 s.\u003c\/p\u003e\n\u003cp\u003eThe \u003cstrong\u003etwo limit contacts\u003c\/strong\u003e are PNP or NPN with 30 VDC \/ 200 mA, optionally 1000 mA; switching point and hysteresis are adjustable across the whole measuring range, the switching delay from 0.0 to 999.9 s, and failsafe behaviour as well. Supply comes from the HART current loop with \u003cstrong\u003e12 … 40 VDC\u003c\/strong\u003e, load R = (UB − 12 V) \/ 21 mA, with reverse polarity protection.\u003c\/p\u003e\n\u003cp\u003eMechanically: holding magnet in \u003cstrong\u003eAlnico 500\u003c\/strong\u003e, measuring face Ø 6 mm spring-loaded with 1.5 mm travel, sensor body stainless steel \u003cstrong\u003e1.4571\u003c\/strong\u003e, PBT GF30 housing, connection either at the side or on top, weight approx. 259 g, system pressure PN 25, protection at least \u003cstrong\u003eIP 65\u003c\/strong\u003e at the electronics.\u003c\/p\u003e\n\u003cp\u003eThree points the manufacturer leaves open and that belong in the planning. \u003cstrong\u003eThe sensor sits with the magnet directly on the hot surface.\u003c\/strong\u003e The measuring face may reach +200 °C, the electronics in the head only +80 °C – how much heat travels into the head is not documented, and above +85 °C the electronics can be destroyed. The \u003cstrong\u003egalvanic isolation applies only between the switching outputs and the amplifier\u003c\/strong\u003e, not against the loop and not against the surface the magnet sits on. And how the \u003cstrong\u003eholding force changes with temperature\u003c\/strong\u003e the source does not say.\u003c\/p\u003e\n\u003cp\u003eTen electrical connections are available – which one carries how many limit contacts is not a free choice: two contacts are only possible on M12 five- and eight-pin, on MIL and on the cable version; on Deutsch DT04 four-pin and on Super Seal, none. Configuration uses the \u003cstrong\u003eHART interface with USB and software\u003c\/strong\u003e, order number 01310-00220; when communicating through a HART modem a resistance of 250 Ω has to be taken into account. No CE marking is documented and no declaration of conformity is available.\u003c\/p\u003e\n\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMeasuring without intervening in the process – holding magnet with 66 N\u003c\/li\u003e\n\u003cli\u003eSpring-loaded measuring face Ø 6 mm, 1.5 mm travel\u003c\/li\u003e\n\u003cli\u003ePt100 4-wire, classes A, B and AA\u003c\/li\u003e\n\u003cli\u003eMedium -50 to +200 °C, up to +250 °C on request\u003c\/li\u003e\n\u003cli\u003e4 … 20 mA with HART, accuracy 0.3 % of the range\u003c\/li\u003e\n\u003cli\u003eTwo limit contacts with adjustable delay\u003c\/li\u003e\n\u003cli\u003eSensor body stainless steel 1.4571, magnet Alnico 500\u003c\/li\u003e\n\u003cli\u003eProtection at least IP 65\u003c\/li\u003e\n\u003cli\u003eVersion with display available as TMMA\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"octogon Shop","offers":[{"title":"Default Title","offer_id":57245618766150,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TMMB_METS-WTM_titelbild_762e2e44-6288-4034-aa0b-09e27d501197.webp?v=1788951932"},{"product_id":"temperatursensor-feder-kontakt-mkts-sp","title":"TSMA Spring-loaded Contact Temperature Sensor (MKTS-SP)","description":"\u003cp\u003eThe \u003cstrong\u003eTSMA\u003c\/strong\u003e is a temperature sensor with a spring-loaded measuring tip, manufacturer type Müller \u003cstrong\u003eMKTS-SP\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIt is built for bearing and surface temperatures: the spring presses the tip against the measuring point with \u003cstrong\u003e14 mm of travel\u003c\/strong\u003e and keeps contact even when the component moves or expands with heat. That is exactly what it is for – a rigidly screwed-in sensor loses contact at such a point.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis sensor does not withstand process pressure.\u003c\/strong\u003e The manufacturer says so in as many words: the process connection has no sealing effect. It measures at the surface and in the bearing, not inside a closed medium; the pressure equipment directive is therefore not applicable.\u003c\/p\u003e\n\u003cp\u003eThe input takes \u003cstrong\u003eone or two Pt100\u003c\/strong\u003e or \u003cstrong\u003ePt1000\u003c\/strong\u003e in 2-, 3- or 4-wire connection in classes A, B and AA, alternatively a \u003cstrong\u003etype K thermocouple with a cross-band\u003c\/strong\u003e. The range runs from \u003cstrong\u003e-50 … +150 °C\u003c\/strong\u003e at a smallest span of 50 K. As with the room sensor there are two versions: resistance directly on the connector, or \u003cstrong\u003e4 … 20 mA with HART\u003c\/strong\u003e in the 2-wire loop.\u003c\/p\u003e\n\u003cp\u003eTotal accuracy is \u003cstrong\u003e0.3 % of the range\u003c\/strong\u003e at \u003cstrong\u003e16 bit\u003c\/strong\u003e, the response time 20 ms, the measuring rate 10 measurements per second, the filter 0 … 99 s, the transfer characteristic linear with temperature. The current range is 3.8 … 20.5 mA with 3.6 mA on short circuit and 21 mA on break. Supply comes from the HART current loop with \u003cstrong\u003e12 … 40 VDC\u003c\/strong\u003e, load R = (UB − 12 V) \/ 21 mA, with reverse polarity protection. Setting is done in software over HART.\u003c\/p\u003e\n\u003cp\u003eMechanically: process connection 3\/8\", 1\/2\" or 3\/4\" without sealing effect, insertion length \u003cstrong\u003e45 or 65 mm\u003c\/strong\u003e as well as custom, sensor tube Ø 6 mm in stainless steel \u003cstrong\u003e1.4571\u003c\/strong\u003e, knurled screw 1.4541, compression spring in 1.4310 spring steel, PTFE insulating body, weight approx. 200 g. Protection is \u003cstrong\u003eIP 65 at the electronics and IP 68 at the sensor\u003c\/strong\u003e, encapsulated inside. Without a transmitter the ambient may be -20 … +100 °C, with a transmitter only -20 … +80 °C.\u003c\/p\u003e\n\u003cp\u003eTwo notes: the ambient temperature is not the medium temperature – which neck length or insulation a hot medium calls for, the source does not say. And the \u003cstrong\u003eMK product code is used three times by this manufacturer\u003c\/strong\u003e – MKTS, MKTS-GL and MKTS-SP, with a different meaning of the following digits in each case; when ordering, the type designation belongs in plain text, not just the code. Ten electrical connections are available; two sensors do not fit every connector.\u003c\/p\u003e\n\u003cp\u003eConfiguration uses the \u003cstrong\u003eHART interface with USB and software\u003c\/strong\u003e, order number 01310-00220. No CE marking is documented in the manufacturer's data sheet and no declaration of conformity is available for this version. The version with IO-Link is the \u003cstrong\u003eTSMB\u003c\/strong\u003e (MKTS-SPIO).\u003c\/p\u003e\n\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSpring-loaded measuring tip, 14 mm ±1 mm of travel\u003c\/li\u003e\n\u003cli\u003eKeeps contact on moving and expanding components\u003c\/li\u003e\n\u003cli\u003ePt100, Pt1000 or type K thermocouple\u003c\/li\u003e\n\u003cli\u003eRange -50 to +150 °C, smallest span 50 K\u003c\/li\u003e\n\u003cli\u003eResistance direct or 4 … 20 mA with HART\u003c\/li\u003e\n\u003cli\u003eAccuracy 0.3 % of the range, 16 bit\u003c\/li\u003e\n\u003cli\u003eInsertion length 45 or 65 mm, sensor tube 1.4571\u003c\/li\u003e\n\u003cli\u003eIP 65 at the electronics, IP 68 at the sensor\u003c\/li\u003e\n\u003cli\u003eVersion with IO-Link available as TSMB\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"octogon Shop","offers":[{"title":"Default Title","offer_id":57245618831686,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TSMA_MKTS-SP_titelbild_2a57f779-2669-4376-8a67-3184cf076f1f.webp?v=1788951932"},{"product_id":"tmma-oberflachensensor-hart-magnet-mets-wsm","title":"TMMA Magnetic Surface Sensor with Display (METS-WSM)","description":"\u003cp\u003eThe \u003cstrong\u003eTMMA\u003c\/strong\u003e is a surface temperature sensor on a magnetic base with a display and two limit contacts, manufacturer type Müller \u003cstrong\u003eMETS-WSM\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIt is placed on pipes, motors, and housings where no drilling is allowed – attached instead of installed, without interfering with the medium. The spring-loaded measuring surface \u003cstrong\u003eØ 6 mm\u003c\/strong\u003e with 1.5 mm travel presses onto the surface, and the Alnico 500 magnetic base holds with \u003cstrong\u003e66 N\u003c\/strong\u003e. The sensor body is made of stainless steel \u003cstrong\u003e1.4571\u003c\/strong\u003e; with approx. \u003cstrong\u003e259 g\u003c\/strong\u003e, \u003cstrong\u003ePN 25\u003c\/strong\u003e and at least \u003cstrong\u003eIP 65\u003c\/strong\u003e for the electronics, the mounting position is arbitrary.\u003c\/p\u003e\n\u003cp\u003eThe device features a four-digit 7-segment display with a head that can be \u003cstrong\u003erotated by approximately 330°\u003c\/strong\u003e and a display that can be mirrored by 180°. Settings are made on the device using \u003cstrong\u003ethree buttons\u003c\/strong\u003e or via HART; the measured value can be read on-site without a host computer. The \u003cstrong\u003etwo limit contacts\u003c\/strong\u003e operate as PNP or NPN with 30 VDC and 200 mA; switching delay and failsafe can be set up to \u003cstrong\u003e999.9 s\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eMeasurement is performed with a \u003cstrong\u003ePt100 in 4-wire circuit\u003c\/strong\u003e in classes A, B, and AA in the range \u003cstrong\u003e-50 … +200 °C\u003c\/strong\u003e with a smallest span of 50 K. The output is \u003cstrong\u003e4 … 20 mA with HART\u003c\/strong\u003e in the 2-wire loop; the accuracy of the measuring amplifier is \u003cstrong\u003e0.3% of the range\u003c\/strong\u003e at 16 bits. The sensor is powered from the HART current loop with \u003cstrong\u003e12 … 40 VDC\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBefore ordering, please note:\u003c\/strong\u003e The ambient temperature is not the medium temperature – the measuring surface can withstand up to +200 °C, but the electronics in the head only up to +80 °C, and above +85 °C they can be damaged; the sensor sits with the magnet directly on the hot surface, the source does not say how much heat reaches the head. How the adhesive force of 66 N changes with temperature is not documented; the fastening must be checked before use on hot surfaces. Galvanic isolation applies only between switching outputs and measuring amplifier, not against the loop and not against the surface on which the magnet sits. Two limit contacts are only available with M12 five- and eight-pole as well as MIL; a cable gland is not listed. The data sheet only mentions up to -50 … +250 °C on request. For configuration, the \u003cstrong\u003eHART interface with USB and software\u003c\/strong\u003e (01310-00220) is used. A CE mark, a declaration of conformity, and explosion protection are not documented in the data sheet. The identical version without display and buttons is the \u003cstrong\u003eTMMB\u003c\/strong\u003e (METS-WTM).\u003c\/p\u003e\n\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\n\u003cul\u003e\n\n\u003cli\u003eAttached instead of installed – magnetic base with 66 N from Alnico 500\u003c\/li\u003e\n\n\u003cli\u003eFour-digit display, head rotatable by approx. 330°, three buttons or HART\u003c\/li\u003e\n\n\u003cli\u003ePt100 4-wire, classes A, B, and AA, medium -50 … +200 °C\u003c\/li\u003e\n\n\u003cli\u003e4 … 20 mA with HART, accuracy 0.3% of range\u003c\/li\u003e\n\n\u003cli\u003eTwo limit contacts, switching delay up to 999.9 s\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"octogon GmbH","offers":[{"title":"Default Title","offer_id":57356931858758,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TMMA_produkt_81355919-023e-421b-8b55-2077eb02789f.webp?v=1789243717"},{"product_id":"tsmb-anlegesensor-gefedert-io-link-mkts-spio","title":"TSMB Contact Sensor Spring-Loaded IO-Link (MKTS-SPIO)","description":"\u003cp\u003eThe \u003cstrong\u003eTSMB\u003c\/strong\u003e is a contact sensor with a spring-loaded measuring tip and an IO-Link interface, manufacturer type Müller \u003cstrong\u003eMKTS-SPIO\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003eIt measures on the surface and in bearings: The compression spring holds the measuring tip with a \u003cstrong\u003e14 mm travel (±1 mm)\u003c\/strong\u003e at the measuring point, even if the component moves or expands due to heat – a rigidly screwed-in sensor would lose contact in such a situation. The sensor tube measures \u003cstrong\u003eØ 6 mm\u003c\/strong\u003e made of stainless steel \u003cstrong\u003e1.4571\u003c\/strong\u003e, the compression spring is made of spring steel \u003cstrong\u003e1.4310\u003c\/strong\u003e, the protection class is \u003cstrong\u003eIP 65 \/ IP 68\u003c\/strong\u003e, the installation length is \u003cstrong\u003e45 or 65 mm\u003c\/strong\u003e, the weight is approximately \u003cstrong\u003e200 g\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003eThe mechanics are the same as with the \u003cstrong\u003eTSMA\u003c\/strong\u003e (MKTS-SP); instead of a HART transmitter, an IO-Link transmitter is installed here. The measured value is sent digitally to the \u003cstrong\u003eIO-Link\u003c\/strong\u003e master, and the sensor is also parameterized there – a configuration device is not necessary, the description of the values is in the device file \u003cstrong\u003eIODD MKTS-SPIO\u003c\/strong\u003e. The electrical connection is \u003cstrong\u003eM12x1 four-pin\u003c\/strong\u003e as the only option; the sensor does not have a display or limit contacts.\u003c\/p\u003e\u003cp\u003eThe input has \u003cstrong\u003ea Pt100\u003c\/strong\u003e in a \u003cstrong\u003e3-wire circuit\u003c\/strong\u003e or a thermocouple \u003cstrong\u003eType J, K or N\u003c\/strong\u003e. The nominal range extends from \u003cstrong\u003e-50 … +150 °C\u003c\/strong\u003e in all versions; a measuring range of \u003cstrong\u003e0 … 100 °C\u003c\/strong\u003e is set ex works, customizable. The source states the accuracy as \u003cstrong\u003emax. 0.02 % of the range\u003c\/strong\u003e plus sensor error at \u003cstrong\u003e16 Bit\u003c\/strong\u003e and \u003cstrong\u003e20 ms\u003c\/strong\u003e response time, powered by \u003cstrong\u003e24 VDC\u003c\/strong\u003e with reverse polarity protection.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNote before ordering:\u003c\/strong\u003e This sensor does not withstand process pressure. The source explicitly states: System pressure not possible, the process connection has no sealing effect; the Pressure Equipment Directive is therefore not applicable. The ambient temperature is not the medium temperature: The electronics in the head tolerate \u003cstrong\u003e-20 … +80 °C\u003c\/strong\u003e, the medium up to +150 °C; the source does not state what neck length or insulation is required for this. The accuracy specification is remarkably favorable: 0.02 % of the range at 16 Bit, while the sister sheets with 24 Bit only guarantee 0.1 % and the MKTS-SP with the same design states 0.3 % – before designing, the value must be confirmed with the manufacturer, the sensor error is always added. The relationship between filter and response time is also striking: 25 s filter at 20 ms response time. The datasheet does not specify a minimum span. A CE mark is not documented, a declaration of conformity is not available; explosion protection is also not documented.\u003c\/p\u003e\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\u003cul\u003e\n\n\u003cli\u003eSpring-loaded measuring tip, travel 14 mm ±1 mm\u003c\/li\u003e\n\n\u003cli\u003eIO-Link with signal level 0\/24 V, parameterization via the master\u003c\/li\u003e\n\n\u003cli\u003eRange -50 to +150 °C, factory setting 0 … 100 °C\u003c\/li\u003e\n\n\u003cli\u003eInstallation length 45 or 65 mm, sensor tube Ø 6 mm made of 1.4571\u003c\/li\u003e\n\n\u003cli\u003eVersion with HART available as TSMA\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"octogon GmbH","offers":[{"title":"Default Title","offer_id":57356932645190,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TSMB_produkt_1b00777b-4c87-4666-b6a6-cf34fa5127d4.webp?v=1789243718"}],"url":"https:\/\/octogon-sensors.com\/en\/collections\/temperatur-anlegen-beruehrungslos.oembed","provider":"octogon GmbH","version":"1.0","type":"link"}